IPMP CONFIGURATION SOLARIS 10 PDF

Oracle Solaris Administration: IP Services Oracle Solaris 10 1/13 Information An IPMP configuration typically consists of two or more physical interfaces on the . For IPMP configuration tasks, refer to Chapter 31, Administering IPMP (Tasks). Oracle Solaris IPMP involves the following software: You can configure one of the interfaces down to 10 megabits and still place the two interfaces into the. You must have configured all interfaces as members of the IPMP group. role to a user, see Chapter 2, Working With the Solaris Management Console (Tasks).

Author: Zolonris Dougor
Country: Japan
Language: English (Spanish)
Genre: Relationship
Published (Last): 21 October 2009
Pages: 13
PDF File Size: 2.52 Mb
ePub File Size: 20.62 Mb
ISBN: 309-5-42980-212-3
Downloads: 80930
Price: Free* [*Free Regsitration Required]
Uploader: Maugami

The transmit or receive path of the interface has failed. In this example, physical interface and data address are paired together.

Physical interface hme0 with the data address Data addresses are the conventional IPv4 and IPv6 addresses that are assigned to an interface of a NIC at boot time or manually, through the ifconfig command. Probe-based failure detection involves the sending and receiving of ICMP probe messages that use test addresses. All requests to detach system components that contain NICs are first checked to ensure that connectivity can be preserved.

Confiyuration a Reply Cancel reply. Planning an IPv6 Network Tasks 5. A multicast packet that is sent to the all hosts multicast address, Troubleshooting Network Problems Tasks The failover feature of IPMP preserves connectivity and prevents disruption of any existing connections. Setup NTP client in solaris 89 and 10 Solaris ip,p Internet Key Exchange Reference Awesome article and nicely explained.

  ANFITRIONE PLAUTO PDF

The probe messages help to determine the health of each interface in the IPMP group. After the daemon receives 10 consecutive replies for a default repair detection time of 20 seconds, the daemon determines that the interface is repaired.

Puppet Automation – Live WebEx. Configguration, This is very good and simple article. If you do use RFC style test addresses, be sure to configure other systems, iomp routers, on the IP link with addresses on the appropriate RFC subnet.

How to configure Solaris 10 IPMP ?

Because IPv6 link-local addresses are usually not present in a name service, DNS and NIS applications do not use link-local addresses for communication. The minimum repair detection time is twice the failure detection time, 20 seconds by default, because replies to 10 consecutive probes must be received. If no replies are made in response to five consecutive probes, in. However, if you must remove the system component, you can override this behavior by using the -f option of cfgadmas explained in the cfgadm 1M man page.

For upmp, you can use the ifconfig command to obtain the status of a standby interface. Avoid using spaces in group names. Ipnp probes verify that the send and receive path to the interface is working correctly.

Add IP interfaces to the group. The following Sun network drivers are supported in the current release of Oracle Solaris: This test IPv6 address is configured only on the next reboot.

Additionally, RCM informs the in. The test IP addresses must belong to a single IP subnet.

Then, the standby interface is treated the same as other active interfaces until the failed interface is repaired. Consult your platform’s documentation for details. RCM records the configuration information associated with any NIC’s that are detached from a running system.

  BFT PHOBOS NL BT PDF

Have the netmask and broadcast address set to the default value. A subnet number or prefix cannot be assigned to more than one IP link. Place each physical interface into an IPMP group. You typically use the cfgadm command to perform DR operations. For more information about target ipmpp use in probe-based failure detection, refer to Probe-Based Failure Confkguration.

Assign the standby interface to the same IPMP group, and configure a test address for the standby interface.

You must set the -failover option before you set the standby up option. Solaris 11 Administration Information Center unixadminschool. Self Paced Courses Live Wolaris. IPv6 in Depth Reference. Link-based failure detection, if supported by the NIC driver Probe-based failure detection, when test addresses are configured Detection of interfaces that were missing at boot time The in.

RCM manages the dynamic reconfiguration of system components. Optional Configure an IPv4 test address on one or more physical interfaces.

How to configure Solaris 10 Link Based IPMP – The Geek Diary

Probe-based failure detection uses target systems to determine the condition of an interface. Internet Key Exchange Overview Introducing IPv6 Overview 4. The only valid IPv6 test address is the solarris address of a physical interface. Administering Network Interfaces Tasks 7.