IPC 9503 PDF

IPC Moisture Sensitivity Classification for Non-IC Components. Content Provider Association Connecting Electronics Industries [IPC]. IPC, PWB Assembly Sol- dering Process Guideline for. Electronic Components. • IPC, Moisture Sensitiv- ity Classification for Non-IC. Components. and Use of Moisture/Reflow Sensitive Surface Mount Devices). This standard supersedes IPC Developed by ECA, IPC and JEDEC.

Author: Shaktijind Dourr
Country: Thailand
Language: English (Spanish)
Genre: Career
Published (Last): 12 February 2016
Pages: 63
PDF File Size: 4.86 Mb
ePub File Size: 13.28 Mb
ISBN: 336-7-28345-915-8
Downloads: 60196
Price: Free* [*Free Regsitration Required]
Uploader: Voodoodal

Components will be covered with a lint free filter paper insert s between the top of the component and the bottom of the cover. A carrier that holds multiple components in a row. Items that are gold plated or have a 16 finish or lower shall contain the following note marked on exterior of container: Surface mount components shall be suitable for vacuum pick up, include caps as applicable.

The parts must not be held in the pockets by supplementary means within the tray. Moisture transfer refers to the fact that certain solid waste Tray covers will also consists of black static dissipative material held to the base with a one piece clip. All components must be loaded into black static dissipative 2″x2″ waffle packs. Suppliers should attempt to provide a best fit solution without incurring extensive tooling costs. All the components shall be oriented in the same direction according to polarity or pin one markings.

Tape and Reel Only General Requirements: Moisture ippc prior to packaging shall not exceed 0. If there are any questions contact Microwave Manufacturing Engineering 6. Each lpc barrier bag may contain up to 10 PWBs of size in2 per side or greater, and smaller boards may be packaged up to 25 per bag. Gel Trays should remain the same for subsequent lots of the same component type.

  BAIXAR NBR 14276 PDF

Use of newsprint, excelsior, or loosed fill expanded polystyrene shall be avoided as a means of cushioning. The preferred cavity size should be mils.

All waffle packs containing items that are ESD sensitive diodes, integrated circuits, etc. The carrier shall have removable stops on each end and shall prevent the components from shifting in any direction. The carrier shall be designed such that the component does not move when the carrier is opened and the lead configuration does not change once the component is removed from the carrier.

Matrix Tray 950 Requirements: Parts do not have to be pre-oriented, but must be face up. Orders over pieces must be supplied on a minimum of two 2 reels or minimum reel package quantity. The lid must be capable of being removed without disturbing the parts within the tray and the part no.

An exception for through-hole radial components, bulkhead-mounted connectors, and cable connectors is best commercial practice. If there are any questions contact Microwave Manufacturing Engineering.

Parts must be loaded consecutively from left to right, proceeding from top to bottom as viewed with the notch of the waffle pack positioned in the upper left hand corner with a consistent separation between rows and columns.

With the notch of the waffle pack in the upper left hand corner, parts must be loaded left to right, and top to bottom. A rigid container that holds one leaded component.

All components must be loaded into black static dissipative 2″x2″ vacuum release trays.

Packaging Requirement Codes

Best Commercial Practice Packaging of parts shall be sufficient to afford protection against deterioration and physical damage during shipment from the supply source to BAE Systems. Components will be covered with a lint free filter paper insert s between the top of the component and the bottom of the cover 4. Solid board packaging is ideal for achieving exclusive. The carrier shall be of a construction to allow component removal without tooling. Each moisture barrier bag shall be marked with the part number, date code, quantity, and serial numbers of the PWBs enclosed.

  CATATAN HATI DISETIAP SUJUDKU PDF

Waffle pack capacity should be maximized within a manufacturing lot. Documents Flashcards Grammar checker. Elements or components that are Class 0 Sensitive shall be clearly marked as Class 0 on the external surface of the packaging.

Packaging Requirement Codes

Parts should be pre-oriented, but must be ippc up. These carriers shall support the body of the component, maintain all physical lead dimensions, and allow visibility of the contact shall be such that no stress is applied to the leads.

Waffle pack covers will also consists of black static dissipative material. Compliance Commitments related to the manufacture and. Basin and Range Province PowerPoint.

Components will be covered with a lintfree filter paper insert s between the top of the component and the bottom cover. Waffle pack dimensions should remain the same for subsequent 5903 of the same component type.

For shelf life requirements beyond one year place a in the Q. Gel Trays must be labeled on the cover and the bottom of the base with the supplier lot number and part number, PO number and BAE part number.