EKC Series – chennai india, EKC Series – chennai, EKC Series – , general ac EKC Series – , EKC Series – , ERC Series – chennai tamil . Temperature controller. EKC MAKING MODERN LIVING POSSIBLE Sensors: Danfoss Pt, PTC or NTC • Calibration of sensors. RI8NB R INSTRUCTIONS. EKC D (B). R Type: Pt Instructions RI8NB © Danfoss 05/ EKC D.

Author: Febar Kazigore
Country: Iran
Language: English (Spanish)
Genre: Health and Food
Published (Last): 15 August 2010
Pages: 362
PDF File Size: 4.94 Mb
ePub File Size: 9.37 Mb
ISBN: 835-8-48749-199-8
Downloads: 1624
Price: Free* [*Free Regsitration Required]
Uploader: Durisar

But you can also use a sensor with another signal accuracy. Refrigeration stopped because of open DI input S Select your own number. If not, you can cancel the function with setting ekcc.

This timer function can be used as a simple way of starting defrosts, but it will always act as safety defrost if one of damfoss subsequent defrost starts is not received. The Danfoss controller is used for applications where temperature is critical. If there is a status code, it will be shown on the display. R22 Medium and high temperature scroll air-cooled condensing unit Box type air outlet from side scroll ZB series. But before you change the value, you must have access to the menu.

HVAC Danfoss Electronic Temperature Controller type Danfoss EKC 102A 084B8500 for Freezer

When you have changed the value save the new value by once more pushing the middle button Examples Set menu 1. An A alarm will not be visible as long as there is an active E alarm.

When the input is open it signals that the door is open. Here you define which: Defrosting S15 Defrost sequence.

The display shows the actual room temperature, but by activating the keys the display changes To the set or the actual temperature of the defrost sensor. The actual defrost will be stopped based on time or temperature with a signal from a temperature sensor.


Select the relevant number. Check delivery time and costs. DO3 is a 8 A relay. Roof mounted industrial Electrical defrosting air cooler low temperature DJ series for cold room. If the defrost sensor registers a higher temperature than the one set here, the fans will be stopped.

RA Box type air outlet from side Medium and high temperature scroll air-cooled condensing unit scroll ZB series. If the function is used, access code 1 o05 must also be used.

Fitting the EKC controller with a plug-in module for communication gives access to all parameters of the controller. The time delay is set in minutes.

Communication error and timeout You can return the product without providing a reason within 14 days. Relay output 2 can be used for alarm function or for cutin and cutout of a refrigeration step 2.

Danfoss Temperature controller – EKC 102

Interval between wkc starts The function is zeroset and will start the timer function at each defrost start. Drip-off time Here you set the time that is to elapse from a defrost and until the compressor is to start again.

See the significance in the Fault Message section. Defrost is started at fixed time intervals, say, every eighth hour Refrigeration time: To avoid a too high setting of the setpoint, the max. When the compressor is operating it must run for at least x minutes. There are no openings that can receive moisture or dirt.

Controller for temperature control – EKC Manual |

E-alarms, on the other hand, will become visible the moment the error occurs. Running times To prevent irregular operation, values can be set for the time the compressor is to run once it has been started. Lower alarm limit Here you set when the alarm for low temperature is to start.


The alarm will not become active until the set time delay has been passed. Fan cut in during defrost Here you can set whether fan is to operate during defrost.

HVAC Danfoss Electronic Temperature Controller type Danfoss EKC A B for Freezer

Standby position stopped refrigeration via r12 or DI input A Activation of reference displacement When the function is changed to ON the thermostat differential will be increased by the value in danfoes If you push the top button in this situation you can see the alarm report in the display. EKC for panel mounting and EKC for DIN-rail mounting have been specially developed for control duties in refrigeration plant so that operation, setting and programming are optimised and simplified as much as possible.

Danfoss reserves the right to alter its products without notice. If the time is passed, a defrost will be started.

Providing personal data is voluntary, but necessary for providing a reply. The next push restarts refrigeration The elc situations can be followed on the display. Temperature signal 2 can be used for defrost stop based on temperature dxnfoss for product sensor. One, two or three relays will cut the required functions in and out — the application determines which: Delay on outputs during start-up Other displays: The running times are not observed when defrosts start.