CINETECH KNP PDF

KNP Web 15,, views · · Colors for Children to Learn With Street Vehicles and Water Slide – Colours Magic Liquids For Kids BinBin. CINETECH > Hard to find / Shortage Pricing, Availability, Datasheet Download, and Product CRJT, CINETECH KNPWJ0R1, CINETECH. Taiwan Wirewound Resistors SQP, KNP is supplied by ☆ Wirewound Resistors Cinetech Ind Co Ltd does not currently advertise comprehensive company.

Author: Daigul Zoloktilar
Country: Cameroon
Language: English (Spanish)
Genre: Technology
Published (Last): 22 August 2010
Pages: 180
PDF File Size: 19.43 Mb
ePub File Size: 14.81 Mb
ISBN: 150-9-76553-766-2
Downloads: 26355
Price: Free* [*Free Regsitration Required]
Uploader: Gorn

Step 4 Solder the other side of the part. Step 4 Grip the part with needle-nose pliers. Method 2 – Flood and suck Used for: In most cases the SMD component is destroyed. Step 1 Place a small amount of solder on one of the three pads.

It therefore competes with other technologies that feature high precision, such as wire wound or bulk metal foil. If this is not possible then tin foil can be cnetech to xinetech the regular components.

3D Glasses – Polarizing

Up to 10WResistance Range: Method 1 – Pin by pin Used for: Two pin SMD component, such as a chip capacitor or resistor, is the easiest to de-solder with cineetch regular soldering iron tip.

Simply heat one side until the solder is melted, then quickly move to the other side until the solder is melted. The solderings should not look like ’round ball’ on either side of the parts.

Finally inspect the pins to check if any solder is left between them. VPGproducing the most precise and stable resistors available: Cypress Semiconductor Cypress Semiconductor.

  BOWERSOCK JULIAN THE APOSTATE PDF

Do the same on the other side of the chip. Step 3 Put a small force down on the part and re-heat the one pad to guarantee that the parts is flat against the PCB. Use needle-nose pliers to hold the part mnp place while heating. A simplified list is included with each method to identify which types of SMD components are for the appropriate method.

Heat the pad already with solder and slide the part onto the pad so that it is centered between the pads. Step 3 Now solder the rest of the pins, one-at-a-time. A properly soldered joint should have a curved line from the end of the pad to the top of the part as shown in the pictures. Make sure the pliers are not bare metal or they will get too hot to handle when heating. Boca Semiconductor Boca Semiconductor. Crescent Frequency Crescent Frequency. If this knpp the cast, there cinetecy too much solder being appied to the joint.

World Products World Products. Small Outline Package – SO. Blow on the part to harden the solder. Maxim Integrated Maxim Integrated.

Do kbp same on the other three sides of the chip.

1,5 – Продукция – РКС КОМПОНЕНТЫ

Tripp Lite Tripp Lite. Get a small screwdriver ready to insert under the part. Continue by flooding the other three rows of pins. New Tunirama New Tunirama. To use this method knpp will need a head gun or a PCB oven.

  DATA STRUCTURES USING C BY A.M.TENENBAUM PDF

On the other hand. Step 2 Grab the part with very fine tweezers. Mount the circuit board in a vise that will not burn when heated.

Calmos Technology Calmos Technology. Quickly remove the iron and using a solder sucker, suck the excess solder from between the pins.

Silicon Standard Silicon Standard. Crystek Corporation Crystek Corporation. Insert the screwdriver under that side and pry up until the pins are off the PCB and out of the solder. Dean Technology Dean Technology.

Cinetech Ind Company Ltd Part Numbers List on Page 5

Without needing the oil baths that conventional standard cinetevh require, national standard institutes and local calibration laboratories in Japan use our standard resistors both for primary and secondary standards. Pico Electronics Pico Electronics Heat the solder on the next pins and do the same until the other end is reached.

Diodes, Capacitors and Resistors in sizes like,,and General Electric General Cineetch.

American Microsemiconductor American Microsemiconductor. Voltage Multipliers Voltage Multipliers. Hosonic Electronic Hosonic Electronic.

Method 3 – Solder paste Used for: Besure the part is flat and aligned, then remove the heat. Heat the other side in the same manner and when the whole row is melted remove the part.