The ASTM E (Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure. Imison. John H. Waskow, P.E.. Architectural Testing, Inc. Test Method: ASTM E , Test Method for Water Penetration of Exterior Windows, Curtain Walls. Purchase your copy of ASTM E – 00() as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards.
|Published (Last):||22 December 2006|
|PDF File Size:||10.33 Mb|
|ePub File Size:||10.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM E | Water Penetration Testing
The ASTM E testing is performed by applying water to the exterior of the test specimen while lowering the pressure inside by means of an air chamber built on the inside or opposite side of the test specimen. The water spray system has nozzles astj on a grid to deliver water so that the test specimen is wet uniformly, includingthose areas vulnerable to water penetration. BDG has extensive knowledge of most building systems and specializes asm forensic water intrusion investigations.
This differs greatly from the AAMA and AAMA field testing procedures that are intended for evaluating newly installed fenestration products or quality assurance testing.
ASTM E331 – 00(2016)
Conducting the investigative testing to verify and extend hypotheses arrived at during the document review and inspection portions of the investigation using controlled and reproducible procedures. The testing pressure differential is usually determined by the testing specifier.
Specifically excluded from this field check method is the testing of operable components such as operable window and doors. This standard is utilized 3e31 laboratory or interior mock up testing only. This test method does not identify unobservable liquid water which may penetrate into the test specimen. This test method exclusively ashm a uniform static air pressure difference.
Water Penetration Field Testing
ASTM states the field test may also be made after the building is completed and in service to determine whether or not reported leakage problems are due to the failure of aetm installed assemblies.
BDG utilizes professional testing equipment that is calibrated to each specific testing standard for accurate results. This standard is utilized for either field quality assurance testing or forensic testing.
Read more about what our customers have to say In service, the performance will also depend on the rigidity of supporting construction and e3311 the resistance of components to deterioration by various causes, vibration, thermal expansion and contraction, etc. SITC determines what procedure to utilize based on the laboratory testing results.
It can only be utilized prior to the issuance of the building occupancy permit and no later than six months after the installation of the fenestration product. See our page for further information.
Give us a call to discuss your next project. In applying the results of tests by this test method, note that the performance of a wall or its components, or both, may be a function of proper installation wstm adjustment.
The AAMA describes steps for calculating the approximate differential air pressures the specimens experienced during actual wind driven rain events. The reviewing of project documents for the building. Water that penetrates the assembly, but does not result in a failure as defined herein, may have adverse effects on the performance of contained materials such as sealants and insulating or laminated glass.
Historical Version s – view previous versions of standard.
Water Penetration Field Testing
Professional services based on accurate information that helps you or your company make the right decision regarding your project or asset.
The air-pressure differences acting across a building envelope vary greatly. Our aetm consultants are properly trained and knowledgeable of all testing standards.
The diagnostic field water check is utilized for installed storefronts, curtain walls and sloped glazing systems only. Building Diagnostics Group, Inc. These systems shall be tested per the AAMA Most generic specifications call for a minimum testing pressure of 6.
The purpose of astk voluntary guideline is to recreate leaks that are known to occur. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM states that the field test may be made at the time the window, skylight, curtain wall or door assemblies are initially installed. These factors should be fully considered prior to specifying the test pressure difference to be used. This allows us to not only properly test fenestrations on new construction projects, but also pinpoint the cause of any test failures and provide accurate recommendations to achieve asfm testing results.
This specification is for quality assurance testing only of storefronts, curtain walls and sloped glazing systems and their installation.