ASTM B122 PDF

ASTM B – Designation: B /B M – 01 Standard Speci?cation for Copper -Nickel-Tin Alloy, C. This standard is issued under the fixed designation B /B M; the number . ASTM designation and year of issue (B/. B M. ASTM B attains the requirements for copper-nickel alloy plates, sheets, strips, and rolled bars made from UNS C, UNS C alloy. Such Sheet or.

Author: Samuzilkree Tagis
Country: Zimbabwe
Language: English (Spanish)
Genre: Science
Published (Last): 25 September 2018
Pages: 141
PDF File Size: 15.79 Mb
ePub File Size: 17.67 Mb
ISBN: 908-4-99363-618-3
Downloads: 27851
Price: Free* [*Free Regsitration Required]
Uploader: Kagalkis

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

When all the elements in Table 1 are analyzed, their sum shall be as follows: D Standard designation de? This specification also contains awtm on the standard tempers for and tensile strengths of hot-rolled, cold-rolled, and annealed tempers.

Cupro Nickel (UNS C, ASTM B)

C M20 H01 H02 H04 H06 H08 as hot-rolled quarter hard half hard hard extra hard spring 38 47 56 67 72 76 [] [] [] [] [] [] 56 63 70 79 84 87 [] [] [] [] [] [] Link to Active This link will always route to the current Active version of the standard. C 4 55 18 C 48 55 63 73 79 [] [] [] [] [] 63 70 77 87 91 [] [] [] [] [] Although no minimum grain size is required, this material shall be fully recrystallized.

  COMPUTHERM 004RF PDF

The molten iron is commonly referred to as hot metal or, in its solid form, as pig iron. Cupro-Nickel are among the most attractive, durable and versatile copper alloys available.

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. C M20 H01 H02 H04 H06 H08 as hot-rolled hard half hard hard extra hard spring 48 56 67 80 89 95 [] [] [] [] [] [] 65 [] 73 [] 82 [] 94 [] [] [] Siddhagiri Metals and Tubes Manufacturer: C Phosphorus at 0.

C 5 70 In case of disagreements, the chemical composition is determined following appropriate methods listed here. Combining values from the two systems may result in non-conformance with the standard.

Users of this standard are expressly advised that determination of the validity of any such aetm rights, and the risk of infringement of such rights, are entirely their own responsibility. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

70-30 Cupro Nickel

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Special or nonstandard tempers are subject to negotiation between manufacturer and purchaser See 5. The values stated in each system are not exact equivalents; therefore, each system shall 1 This speci?

  EPICYCLIC GEAR CALCULATIONS PDF

Offer on Fasteners B1222. Billets are rolled into bars, rods.

C 9 70 10 C 8 59 12 C and C to this standard in and Tables Atsm properties for other tempers shall be agreed upon between manufacturer and purchaser at the time of placing the order.

A slab, also from ingot, has a rectangular cross-section, with b122 area of at least cm2 and width at least three times the thickness. Combining values from the two systems may result in nonconformance with the speci?

ASTM B Copper Nickel Sheet Plate Supplier · B C/C

The B and F scale hardness values apply to metal 0. C Rockwell hardness values apply as follows: B Scale 68—82 80—90 87—94 89—96 Super?

The following alloys are covered: Steel ingot is the cast metal with porosity and blow-holes. The derived SI unit for force is the newton Nwhich is de?

The minimum weight of the composite sample shall be g.