ASTM A991 PDF

ASTM A – Designation: A /A M – 98 (Reapproved ) Standard Test Method for Conducti. Purchase your copy of ASTM A/AM – 17 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. This standard is issued under the fixed designation A/AM; the number This test method is under the jurisdiction of ASTM Committee A01 on Steel, 2.

Author: Kagaktilar JoJor
Country: Ghana
Language: English (Spanish)
Genre: Travel
Published (Last): 13 February 2012
Pages: 400
PDF File Size: 11.98 Mb
ePub File Size: 10.79 Mb
ISBN: 947-6-61566-865-5
Downloads: 98890
Price: Free* [*Free Regsitration Required]
Uploader: Maurn

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Results of the application of this test method shall be expressed as a variation from a temperature set point. Interpretation of Results and Establishment of the Working Zone 9.

Historical Version s – view previous versions of standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A number in parentheses indicates the year of last reapproval. Your comments will receive careful consideration asrm a meeting of the responsible technical a99, which you may attend. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

ASTM A991/A991M – 17

The values stated in each system are not exact equivalents; therefore, each system is to be used a9911 of the other, without combining values in any way.

Documentation of Survey Results 8. A major furnace modi? Examples of these surveying techniques are listed below. Combining values from the two systems may result in non-conformance with the standard.

For proposed working zones greater than, or equal to, 12 in. The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon by the purchaser and supplier. Starting time and chart speed shall be marked on the original temperature charts, 8. Heat Treatment in the Working Zone This method is used to determine the capability of the furnace to meet the permissible temperature variation specified in the applicable product specification, or as agreed to by the purchaser and supplier of heat treat services.

  BIJUTERII DIN MARGELE CROSETATE PDF

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Survey documentation requirements, and the procedure used to subsequently establish the furnace working zone, are defined in this test method. Link to Active This link will always route to the current Active version of the standard. AMS Pyrometry3 3. The working zone may be comprised of one or more heating zones in the furnace. Survey documentation requirements, and the procedure used to subsequently establish the furnace working zone, are de?

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

In each test, determine the temperature variation pattern at one or more of the test locations.

Furnace Survey Equipment 5. The rate of conveyance shall be representative of normal operating conditions. Originally approved in Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are asgm provided as part of the standard. Details of this procedure shall be as agreed to between purchaser and supplier. The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon by the purchaser and supplier.

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. All other conditions described in 6. Calibration to such national standards shall be done at least once every two years.

  BS EN 12350-7 PDF

Current edition approved Oct. Regardless of heat treat furnace type, or processing cycle, it may be s991 for users to know the temperature uniformity wstm the furnace and whether the material is processed in w991 zone within the furnace that is capable of ashm the applicable permissible temperature variation requirements. It provides validation of temperature uniformity by a series of tests rather than a single test.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM International – Standard References for ASTM A / AM – 17

Aastm them at the outer extremities, the center of the proposed working zone, and in areas of suspected variability in the proposed working zone. Attach survey test sensors to, or set them in the load. Regardless of heat treat furnace type, or processing cycle, it may be necessary for users to know the temperature uniformity in the furnace and whether the material is processed in a zone within the furnace that is capable of meeting the applicable permissible temperature variation requirements.

Within the text, the SI units are shown in brackets. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Use of representative material to simulate product during survey is permitted. This method is used to determine the capability of the furnace to meet the permissible temperature variation speci?