AMERCOAT 253 PDF

Amercoat Chemical Resistant Lining. Product Data/. Application Instructions. • High Solids, high performance epoxy novolac also defined. Amercoat – Download as PDF File .pdf), Text File .txt) or read online. This Safety Data Sheet is prepared in accordance with Annex II to Regulation ( EC) No. / AMERCOAT CHEMICAL LINING CURE.

Author: Dazragore Malazuru
Country: China
Language: English (Spanish)
Genre: Art
Published (Last): 2 May 2010
Pages: 136
PDF File Size: 6.68 Mb
ePub File Size: 7.6 Mb
ISBN: 852-6-63014-772-1
Downloads: 87013
Price: Free* [*Free Regsitration Required]
Uploader: Doujar

See Dry Schedule Table Cure: View companies and products as a list. Adding too much accelerator may will adversely affect the recoatability, appearance, and performance of the products.

Material which has begun to set is unsatisfactory and must be discarded.

Amercoat 253 pdf

Use a spray tip size of “. Once dry, perform surface preparation and apply Hi-Temp in accordance with the data sheet on all areas where the existing paint has been removed. Mixed paint amsrcoat ready for use. Add the following amounts for these products: Variations in the application environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results.

Do not apply at substrate temperatures below 50 F [10 C] or above F [66 C]. Apply two coats of Hi-Temp VS at 2 to 2.

Do not thin VHA with any other solvent. Typical equipment is as zmercoat F C 8 months Surface Preparation Carbon Steel Coated surfaces must be dry and free of weld splatter, oil, dirt, grease and all other contaminates.

Call for prices Details.

  ASCOT GAVOTTE PDF

Dedicated airless equipment is highly recommended. Slowly add powder under moderate agitation in a vortex. A test patch of PSX over in-tact clean coating and observation for film defects and adhesion over a period of time may be required, dependent upon the type of coating.

Galvanized surfaces that have been passivated with a chromate treatment must be abrasive blasted. Surface Preparation Coating performance is, in general, proportional to the degree of surface Amercoat Amercoat Storage temperature should be F and in dry conditions. Safety precautions For paint and recommended thinners see relevant material safety data sheets.

Protective Coatings Product Catalog AMERCOAT. A PPG brand

This also allows Hi-Temp VS to have superior color stability as compared to most generic silicone topcoats, which tend to discolor at elevated temperatures. Maximum recoating time is highly dependent upon actual surface temperatures not simply air tem peratures.

Discoloration does not impact performance. To extend the useful service life of the aged or new asphalt built-up roof system and to reduce cooling More information. Material temperature must be maintained at 60 to 90 F at the time of application. Quikspray Carrousel pump equipped with a hopper feed, spray gun and material lines can also be used. Thinner Amercoat 65 or Amercoat Cleaning solvent Amercoat 12 Cleaner or thinner Safety precautions For paint and recommended thinners see safety sheetand relevant material safety data sheets This is a solvent borne paint and care should be taken to avoid inhalation of spray mist or vapor as well as contact between the wet paint and exposed skin or eyes.

  AJAHN SUMANO PDF

Colors are approximately and will tend to change over time. Roller patterns will be visible when using the aluminum color.

SML Marine Paints – Amercoat by Ameron is comparable to Tankguard Sp. Topcoat

When brushing and rolling, use only quality brushes and rollers. Flush equipment with Hi-Temp 5 Thinner before using equipment. My boat went back in the water today! It is visually aemrcoat, layered. A rating of 4 or higher indicates sufficient cures. Extreme caution should be taken to ensure there is no ice on the surface in cold weather.

Amercoat – [PDF Document]

Rinsing should be done with clean water until the surface ph is 8 or lower as a,ercoat in several locations. Use standard conventional spray guns. Cross spray at right angles to first pass until the specified thickness is achieved. This data sheet supersedes all previous versions and it is the Buyer s responsibility to ensure that this data sheet is current prior to using the product.

Ensure brush is well loaded to avoid air entrainment. For paint and recommended thinners see safety sheetand relevant material safety data sheets This is a solvent borne paint and care should be taken to avoid inhalation of spray mist or vapor as well as contact between the wet paint and exposed skin or eyes.