Westell/Versalink Gateway W Manual. products/pdf/ The Westell® VersaLink™ Gateway provides reliable. w) u • Read online or download PDF • Westell Technologies Versalink W User Manual. Westell W came out in and is still in use today as a simple and powerful DSL modem. Not only is the Westell W a wireless modem, it is also a wired.
|Published (Last):||7 March 2016|
|PDF File Size:||9.1 Mb|
|ePub File Size:||13.14 Mb|
|Price:||Free* [*Free Regsitration Required]|
Beginning of Diagnostics Help screens VersaLink status checks the connection. This screen 37w an advanced diagnostics screen. If you click on Cancel, the new settings will not be saved. Figure 12 may pop up, depending on how Windows 98 SE was installed on the computer. Otherwise, the 20 uses slot time is used.
The arrows show the data path for each flow. The WAN Configuration screen will be displayed.
The following pop-up screen will be displayed. Items you will need Ethernet cable Phone line. The Getting Started screen will be displayed.
Ensure that an Westell has developed an extensive list of NAT services and you may select kanual service from this list. This screen will retrieve the software update file and display any available update information.
The password should be at least 4 characters long mannual should not exceed 32 characters. Windows will display the location of the driver Figure Internet service provider subscriber software and connection requirements may vary. The equipment cannot be repaired in the field. The following instructions explain how to install VersaLink for simultaneous use of Ethernet and Wireless ports. Windows will search for the driver.
Westell Technologies Versalink 327W User Manual
This screen is used to update the firmware that controls the operation of VersaLink. If you need to reset VersaLink to factory default settings, push the reset button on the rear of VersaLink.
OUT-Fragments The number of successful transmissions made. If you clicked on OK in the preceding screen, the following screen will be displayed. HOME As you navigate through the various screens of VersaLink, the name of the active page that you have selected will appear in the upper-left corner of the screen, as shown below. Windows 98 SE Note: If you click on Cancel, your new profile settings will not be saved.
It alerts you of noteworthy information sent to VersaLink from the Internet.
Factory defaults become current configuration. The rates are broadcast 327s the connection protocol as rates supported by the VersaLink. The type of message displayed depends on the menu that you are viewing. Prior to freelance writing, Johnson taught English in Japan. If the Gateway is password protected and you are not an authorized user, you will not be able to change the values.
To print the manual completely, please, download it. The following screen will be displayed as VersaLink is being reset. Not only is the Westell W a wireless modem, it is also a wired modem that has 4 Ethernet jacks for different computers or other devices. This screen allows you to upgrade the software on VersaLink.
Click on OK in the pop-up screen.
The Install Hardware Device Drivers window appears. Click Browse… and go to the location where the upgrade file is stored. The default SSID for VersaLink is the serial number of the unit located below the bar code on the bottom of the unit and also on the Westell shipping carton. If you click OK, you will allow incoming connections to be forwarded to a designated local PC. If you clicked on save, in the preceding Majual Configuration screen, the following pop-up screen will appear.
WESTELL TECHNOLOGIES W USER MANUAL Pdf Download.
Refer to section 20 in this User Guide for further details. Click on close to accept the changes, or click on add to go back to the Trigger Ports screen and enter additional port range values.
The updated firmware may be loaded from either a file that is located on your PCs hard drive or from majual files stored on an Internet server.
Manula you enable Single Static IP, you must reboot your computer. The screens below show that the file upload has completed and that the Programming Flash is being erased to prepare the Flash storage area for upload of the new file.
After you have selected a service, click enable. A Wireless device must be connected to the Gateway for the fields in this screen to be populated. This screen allows you to change the security parameters on your Inbound and Outbound Firewall rules via the User Defined 327ww Rules drop-down arrow.
If you clicked add, the following screen will be displayed. If you clicked OK in manuap preceding screen, the following screen will be displayed.